Re: most bang for buck with ~ $20,000

From: Kenji Morishige <kenjim(at)juniper(dot)net>
To: Scott Marlowe <smarlowe(at)g2switchworks(dot)com>
Cc: pgsql-performance(at)postgresql(dot)org, kenjim(at)juniper(dot)net
Subject: Re: most bang for buck with ~ $20,000
Date: 2006-08-08 22:15:03
Message-ID: 20060808221503.GD6418@juniper.net
Views: Raw Message | Whole Thread | Download mbox | Resend email
Thread:
Lists: pgsql-performance

Great info, which vendor were you looking at for these Opterons? I am goign
to be purchasing 2 of these. :) I do need 24/7 reliability.

On Tue, Aug 08, 2006 at 05:08:29PM -0500, Scott Marlowe wrote:
> On Tue, 2006-08-08 at 15:43, Kenji Morishige wrote:
> > I've asked for some help here a few months ago and got some really helpfull
> > answers regarding RAID controllers and server configuration. Up until
> > recently I've been running PostgreSQL on a two year old Dual Xeon 3.06Ghz
> > machine with a single channel RAID controller (previously Adaptec 2200S, but
> > now changed to LSI MegaRAID). The 2U unit is from a generic vendor using what
> > I believe is a SuperMicro motherboard. In the last week after upgrading the
> > RAID controller, the machine has had disk failure and some other issues. I
> > would like to build a very reliable dedicated postgreSQL server that has the
> > ultimate possible performance and reliabily for around $20,000. The data set
> > size is only currently about 4GB, but is increasing by approximately 50MB
> > daily. The server also requires about 500 connections and I have been
> > monitoring about 100-200 queries per second at the moment. I am planning to
> > run FreeBSD 6.1 if possible, but I am open to any other suggestions if it
> > improves performance.
>
> This really depends on your usage patterns.
>
> OLAP or OLTP workloads? Do you need 24/7 reliability and therefore a
> two machine setup? There's a lot of variety in load.
>
> Generally, you spend your money on disks, then memory, then CPU, in that
> order.
>
> Look at the Areca cards, they've come highly recommended here. Look at
> LOTS of drives. Given the size of your db, you can go with LOTS of
> smaller drives and get good performance. If you can find a good box to
> hold 12 to 16 drives and fill it with 37 gig 15k RPM drives, you'll have
> lots of storage, even in RAID 1+0 config. That's aiming at
> transactional throughput.
>
> Toss as much memory as is reasonably affordable at it. That's normally
> in the 4 to 8 gig range. After that things start to get expensive fast.
>
> Multiple - dual core CPUs are a good idea. Opterons seem to be better
> "data pumps" with large memory and >2 CPUs than Intels right now.
> Better to have a 2xdual core opteron with slower processors than a
> single dual core or dual single core CPU(s) with a faster clock speed.
> As long as the memory access is equivalent, the more CPUs the better in
> Opterons, where their interconnect speed increases as you increase the
> number of CPUs. Intel Xeons are the opposite. Better with fewer faster
> CPUs / cores.
>
> I just ran through a configurator on a site selling quad dual core
> opteron servers. 8 Seagate cheetah 15k rpm drives, 8 gig ram, and the
> slowest (1.8 GHz) AMD dual core CPUs (4 of them) for 8 cores, came out
> to $13,500 or so.
>
> I'd take the other $7.5 grand and buy a backup server that can old as
> much but isn't quite as beefy and set up slony to have a live hot spare
> sitting ready. Oh, and maybe to buy some spare parts to sit in the desk
> drawer in case things break.

In response to

Browse pgsql-performance by date

  From Date Subject
Next Message Steve Atkins 2006-08-08 22:16:52 Re: most bang for buck with ~ $20,000
Previous Message Scott Marlowe 2006-08-08 22:08:29 Re: most bang for buck with ~ $20,000